TopSolid'Steel - Demonstration Library

• - Tread support for central stringer
  • Correction of manual naming
• - New component Wooden step on flats
  • Correction of tread material
  • Correction of the position of the left front flat on step T2
  • Correction of the position of the left rear flat on T7 and T6 steps
  • Correction of the suppression of the left front flat when length is too small
  • Correction of a problem when the flat is removed but not the screws

• - Tread support for central stringer
  • Correction problem on back flange at 180°
  • Correction problem on back flange notch
• + New Wooden Tread on flats component

• - Bolt kit
  • Correction of an processing part problem
• - Tread support for central stringer
  • Correction problem on back flange on other value than 90°.
  • Correction problem on back flange at 180°.
• - Extruded bars
  • Correction of a problem on local extruded bars
  • Drivable description for the flat section
  • Adjustment of simplified representation of finned bar
• + Laminated glass
  • Management of polished edges

• -Tread support for central stringers
  • Correction of a bug of line merging in some cases

• -Bar Nesting
  • Correction of a problem with the reversal of the bar nesting
  • Verification / Correction of the reversal properties for TopSolid'7.17
  • Addition of the bar setting nesting on wood profiles
• +Tread support for central stringers
  • Addition of manual description (Naming tab)
  • Addition of Part number driver (Naming tab)
  • Correction of an error on the back bend on half turn stairs
• +Bolt
  • Correction of an accessory diameter problem when automatic diameter change for the screw
  • Control of the screw material
• -Clearance hole process
  • Correction of a failure problem
• +Basic 2D Grid Layout
  • Removed profile mode for lettering
  • Added pattern modifiers
• -Fixed translation problem on rectangular tubes

• + New ranges of components for Railings:
  • Angle
  • Vertical bars, horizontal bars and with sheet metal fillings
  • Multifunction Posts slab mounting
  • Post for stairs
• + New processes with EN 1090-2 norm extended for screw less M12
• + Hollow square, new codes:
  • 30 x 4
• + Hollow rectangular, new codes:
  • 30 x 15 x 1.5
  • 30 x 10 x 1.5
  • 40 x 10 x 1.5
  • 40 x 10 x 2
  • 50 x 10 x 1.5
  • 50 x 10 x 2
• + Standard extruded bars:
  • Material S235 / S275 / S355 driver adding
• + Hollow circular, square and rectangular
  • Weld + position drivers adding
• + Cutting for railing post
  • New top post positionning
• + Staircase layouts:
  • New las landing and first tread positionning
• + End to end for flats assembly kit
• + Sleeve for hollow section assembly kit
• - Spiral Staircase Layout
  • Headroom correction for multi turn staircase
• - Sheetmetal tread support for central stringer
  • Correction of a clash problem for back bend when angle is greater than 116°
  • Tread fixing drillings + pattern publishing
  • Add possibility do separate the front bend

• Sheetmetal tread support for central stringer
  • Correction of a problem on back bend for angle = 0

• Sheetmetal tread support for central stringer
  • Correction of the cutting problem on the front bend

• Spiral Staircase Layout
  • Add angle in the text
  • Add possibility to control the angle of the staircase

• Spiral Staircase Layout
  • Correction of the orientation of the shape to allow for the splitting of the stringer

• Spiral Staircase Layout
  • Correction of translation problem for FR
  • Management of the angle and lateral offset for the extended landing
  • Addition of a shape to allow for the splitting of the stringer

• Sheetmetal Tread Support For Central Stringer
  • TopOffset for front and back bends management
• Screw Kit
  • Correction of the washer repetition
• Spiral Staircase Layout
  • Management of extended landings
  • Improved consideration of headroom
  • New calculation method for the headroom
  • Added error message when constraints cannot be respected
  • Added new images for drivers
  • New Central Stringer Surface option
  • Correction of the offset for the Central Stringer

+ Boxed Central Stringer
     New calculation of the curvature and orientation of the stringer to maintain a constant thickness regardless of the stiffness of the treading line
     New management of the Normal orientation mode to avoid breakage and twisting
     Improvement of the orientation of the reinforcement plates
     Independent management of the orientation of the reinforcement plates
     Management of the reinforcement plates clearance
     Start and end plate clearance management
     Improvement of the marking system
     Management of multi-segment profiles for stringboard installation

- Multi-flight staircase with basic landing: Modification of the lower limit of the flight length

- Correction of an export problem for Bolt component with Locknut option
- Adding of a new distribution mode for Tenons mortises kit (Quantity + length)
- Correction of a translation problem for straight stairecase layout